Spa Chemicals – Page 2

Spacare Crystal Clear(Clarifier) 500mL

SKU: LC-CC500

Dosage:
Add 100ml per 1000 litres of water every fortnight.

Directions:
Ensure that your spa/hot tub water is correctly balanced.
Clean the filter(s) prior to using Spa Care Instant Filter Klenz for cartridge filters.
Add the required amount of Crystal Clear to the spa/hot tub (see dose rate above).
Run the circulation pump for a minimum of 1 hour.

Repeat the dosage on a fortnightly basis and when refilling the hot tub/spa.

NOTE:
When there is a heavy bather load, an extra dose is advised as there will be additional body fats in the water which could cause cloudiness and foaming.

Spacare Instant Filter Klenz 500mL

SKU: LC-IFK500

Directions for use:
1. Wear protective gloves and use outdoors/well ventilated area. Avoid use on windy days.
2. Remove filter/s from the filter compartment.
3. Rinse the filter/s with fresh water, a hose pipe is ideal to remove loose pollution from the filter.
4. Turn the nozzle on the trigger spray applicator from the STOP to SPRAY position.
5. Thoroughly spray the filter with Instant Filter Klenz taking care to penetrate the filter veins with product.
6. After use turn the nozzle of the spray applicator from SPRAY to STOP and store the bottle safely.
7. Leave the filter/s to stand for a minimum 15 minutes.
8. Rinse the filter/s thoroughly with fresh water from a hose pipe - at this stage foaming may occur.
Continue rinsing until foaming stops.
9. Heavily soiled filters may require a second application.
10. Once the filters have been thoroughly cleaned and flushed, they can be returned to the filter compartment of your spa or hot tub.

Spacare Leak Sealer 500ml

SKU: LC-LS500

Application:
1. Remove all cartridge filters, or for sand filters select the BYPASS option (if applicable) prior to dosing the product.
2. With the pump running add the required dose of Leak Seal slowly through the skimmer or in front of any other suction intake.
3 Leak Sealer is very heavy and will sink to the deepest point, which in most cases will be below the bottom drain, therefore the product must be stirred back into suspension every 45 minutes, whilst the water circulates.
4. Leave the water circulating for a minimum of 3 hours after which time check to see if the leak has stopped (if visible) and/or check the water level. if the leak has slowed down continue to run the circulation system for another 3 hours.
5. When the leak has stopped turn off the pump and let any residue settle to the bottom of the spa. This can then be removed with a suitable spa vacuum.
6. Replace the cartridge filters and let the system circulate for 45 minutes, after which time remove the cartridges and thoroughly clean with fresh water to remove any product residue from the filter veins.
7. After the leak has stopped, it is recommended that the spa/hot tub is fully drained and left empty for a minimum of 48 hours to allow the product to cure.

PLEASE NOTE:
The leak may be slowed down after one application, if this is the case we recommend a second application.

Dosage:
Add 120ml of Leak Sealer per 1000 litres of water.

Spacare Mineral Spa 1kg

SKU: LC-MS1

Directions for use:
Distribute the correct dose of Spa Care Mineral Spa evenly around the spa with the pump running.
It can take up to 12 hours to dissolve
Wait till it is totally dissolved before using the spa
It is recommended to give the filter a quick clean after the dose of Spa Care Mineral Spa has dissolved

Dosage
Initial Dosage:
Add 1kg per 1,500 litres of spa water.
Also when refilling or topping up the spa with fresh water add 1kg per 1,500 litres of water added to the spa

Maintenance Dosage:
Add 100gm per 1500 litres of spa water fortnightly when spa is being used on a regular basis.

Note:
Application rates indicated are to be used as a guide only, consult your local pool professional for more information.

Spacare Mineral Spa 3.5kg

SKU: LC-MS3.5

Directions for use:
Distribute the correct dose of Spa Care Mineral Spa evenly around the spa with the pump running.
It can take up to 12 hours to dissolve.
Wait till it is totally dissolved before using the spa
It is recommended to give the filter a quick clean after the dose of Spa Care Mineral Spa has dissolved.

Dosage
Initial Dosage:
Add 1kg per 1,500 litres of spa water.
Also when refilling or topping up the spa with fresh water add 1kg per 1,500 litres of water added to the spa

Maintenance Dosage:
Add 100gm per 1500 litres of spa water fortnightly when spa is being used on a regular basis.

Note:
Application rates indicated are to be used as a guide only, consult your local pool professional for more information.

Spacare No More Foam 500mL

SKU: LC-NMF500

Directions:
1. Shake the bottle well before opening and using
2. When foaming occurs add 2 or 3 capfuls of NO More Foam
3. If foaming persists repeat the application

Professional Tips
1. Always apply No More Foam with the pump running to help distribution
2. When foam is present in your hot tub or spa it is a sign that your water is out of balance, in particular high levels of unwanted dissolved compounds.
3. These arise from sweat, oil, shampoo and soap that wash off users of the spa or hot tub. Combined with higher running temperature, vigorous agitation of the water and the introduction of air.
4. Always encourage users to shower before use to help minimise foaming of the water.
5. Over dosing with No More Foam can reverse the process and actually increase foaming over time.

Please Note
No More Foam does not remove or inactivate foam casing compounds, it only temporarily reduces their ability to produce foam.

Spacare pH & Alkalinity Reducer 500g

SKU: LC-REDU500

Total Alkalinity & Instructions for dosage:
Add 24gm of pH & Alkalinity Reducer per 1000 litres of water to lower Total Alkalinity by 10 parts per million (ppm)

Directions for use:
calculate the required amount of pH & Alkalinity Reducer (see dosage above). Dissolve in a bucket of water, then poor slowly into the water with the pump and filter operating. Circulate water for 3 hours and then re-check with a test and repeat if necessary.

Spacare pH Up 500g

SKU: LC-PHUP

Directions:
Test the pH of your spa or hot tub water
If the reading is below 7.2, use pH Up to raise it according to the dosage chart below:
Below 6.8 10g for every 1000L
6.8 - 7.0 8g for every 1000L
7.0 - 7.2 6g for every 1000L

Applications Instructions:
Pre-dissolve the product in a clean plastic container of clean warm water.
Stir well to ensure product is fully dissolved.
Carefully add the solution to the spa or hot tub whilst the pump is turned on, preferably near the water inlets to aid distribution.
After a minimum of 6 hours, rechech the pH level and, if necessary, repeat the treatment until the ideal pH is obtained.
Please note a number of treatments may be required.

Spacare Polish and Protect 500ml

SKU: LC-PP500

Directions:
Always ensure the surface to be treated is clean and free from debris.
Turn the nozzle on the trigger spray applicator from the STOP to SPRAY position.
Apply Polish & Protect via the following methods:
Using a clean soft cloth spray Polish & Protect onto the cloth, ensuring the cloth becomes damp, and apply using circular motions ensuring all the required area is treated.
After application allow to air dry for a few minutes.
Buff off lightly with a clean dry cloth.
After use turn the nozzle of the spray applicator from SPRAY to STOP and store the bottle safely.

Spacare Rapid Shock 1kg

SKU: LC-SHOCK1

Directions for use:
Sprinkle over surface of water with pump and filter turned on
Rapid Shock will dissolve within 2-3 minutes
Spa or hot tub may be used 15 minutes after treatment
Dosage rate:
Initial dose - 75g per 1000 litres of water
Regular dose - 50g per 1000 litres of water
Frequency:
Weekly